How To Build A Three Rail Horse Fence

A board on board fence is essentially a fence that consists of central wood posts with wood fencing panels on either side. Therefore, the solution is to fix a timber plate, normally 100 x 50mm in size, on to the wall to which the fence is connected. It looks like you want total privacy or close to it. I would move to the new design and pop a support post in between your existing posts – they don’t even need to pop over. A slip-board fence consists of posts with 2, 3, 4, or more rails and no pickets. Gravel board is treated timber about 180mm (7in) wide and 25mm (1in) thick and is used to keep the bottom of fence panels and featherboards off the ground. You’ll probably be required to submit a fence plan with the completed application.

The trade off is that you will have to do more maintenance to the fence over the years, but if you are prepared for this it is no hardship. It would be helpful to mark your posts showing the base of where the gravel board will end up to ensure you do not sink your post in too far or not enough. Check the location of the fence against an official survey of the lot to make sure the fence is on your property.

If you supply us with the accurate measurement for the length of the closeboard fence run and the overall height of your required garden fence we are happy to work it all out for you. A shorter fence that surrounds a small backyard might only cost a few hundred dollars while others need a fence that surrounds a large yard or a yard of an unusual shape. Dig your first fence post hole with a post hole digger, making sure that the hole is deep enough for about 1/3 of the length of the post to be underground.

This will show you exactly where the next hole should be. Remove the gravel board and dig the next hole. These are available as an extra upgrade from the standard back weathered fence post. This is a very convenient method if the boards are longer than the gaps in the fence and saves you having to cut them to size. As you install the fence boards this string will guide the height at which you set them.

Six foot is normal for a privacy fence, a livestock fence four feet high is usually sufficient, and picket fences are often three feet high. We do concrete materials for fencing (concrete gravel board 6FT x 6 inch 7.00 £, concrete gravel board 6FT x 12 inch 10.00 £, concrete slotted 8Ft post 13.00 £). Each subsequent board can then be fixed to the one below it as shown above and to get the spacing right a small block can be used to ensure an even overlap. The first step in figuring out how much wood is needed to build a fence is to measure the length.

Determining how much a board on board fence costs involves factoring in the cost of the materials and labor. At Penrod Lumber and Fence Company, we have a long-standing tradition of building quality horse fencing. Planning permission is also needed if the fence is above 1m (3ft 3in) and faces onto a public highway or pavement. If you love the style of a board on board fence and want to make an investment in a fence that will last for generations, you can also choose to build a vinyl board on board fence.

First, to assess what you need in terms of materials, measure out the area that you want to fence using a measuring tape or measuring wheel. Posts should be a minimum of 100x100mm (4 x 4) section and concreted into the ground at a depth of approx 760mm (for taller fence variations) and the distance between the post centres should ideally not exceed 3.0M (10Ft). For example, spacing the fence boards on both sides of the rails (commonly called a good neighbor fence) will allow more visibility than butting them up close together on the same side of the rails for more privacy. Now up here in remotish Alaska, there’s not a whole lot of privacy fence building.

And the tops are cut off with a circular saw so all the fence posts now stick out of the ground the same height. Here is a 4 board fence using the same rough sawn wood pictured above for the pasture fence, in a residential setting. The gravel board is normally of a hard timber (such as oak) to withstand the damp rising from the ground. What makes this fence so strong and durable is the fact that Frederick Fence uses pressure-treated posts that are set in the ground at least 36 inches and filled with concrete, meaning the posts won’t give and will stay in place and survive the harshest of weather patterns.

The method of post and rail construction are given on this page , this page on Board Fencing addresses the cladding of the posts and rails. Most use concrete for strength and to protect the wood from direct soil contact. Using metal post supports is a quicker and easier alternative, although your fence won’t be as solid. Once the fence is complete, finish it on the top with a dust cover, nailed directly over the heads of the vertical boards.

This is usually about 22mm to allow the gravel board to be flush with the face of the post. When you build your gate(s),be sure you make your double gates about 1 in. narrower (both gates together) than the opening (or a single gate about 3/4 in. smaller) to allow for opening clearances. Make sure to check the frame for square by measuring the length of the diagonals—they should be the same (Fig.

Gravel boards are placed beneath the fence panels and can be used to gain extra height for the fence, they also lift the timber panels off the ground so they are less likely to rot. Mark the location of the corners as well as any place the fence will change directions. Contact us today or call us at 301 663-4000 and we’ll send out one of our consultants who will be happy to discuss how a board on board fence solution may be the right one for you! What I have put together here is a crude series of diagrams to show how you can build an extremely durable and long lasting fence with horizontal boards.

Fence posts can be secured in the ground with concrete or metal post spikes Here we are looking at how to construct a close-board fence with the posts concreted into the ground. Homeowners can either stain or paint the wood to a color that matches or complements their home or even their patio furniture. Hold the feather edge board on top of the now fixed gravel board and transfer the marks to the face of each post. Reduce total project cost by having multiple vendors bid on the same, detailed work specification of your Board on Board Fence project.

Expert advice and ideas for planning a fence that looks great and does exactly what you want it to do. That’s high enough for visual privacy but low enough so you can visit with neighbors through the jail bars” near the top. To increase privacy, buffer a prevailing wind, or simply add a homey touch, surround your yard with an ornamental and functional fence.