Vise Wikipedia

A solid bench vise is like an extra set of very strong hands, and having one can actually improve your work: As long as it’s attached to a sturdy workbench, a bench vise will hold a workpiece in a still and relatively vibration free state and help you make smoother saw cuts, more steady plane strokes, or even get your sanding done faster. Vises, particularly the rapid-acting type, that are not properly lubricated will be difficult to open and close, resulting in strain on the vise or the operator. I’m a huge fan of the Bench Crafted glide but after having to readjust it a few times in the past few months I’ve often found myself wondering if there was a better way. Should I want to clamp a board across the front of the bench with a space between the apron and the board, I would simply place a spacer at the back of the vise first. With even a small quick-action vise the dog hole strip is still pretty far from the edge.

Woodworking vise advice / rockler how-to, A solid bench vise is like an extra set of very strong hands, and having one can actually improve your work: as long as it’s attached to a sturdy workbench, a bench. Running with glue even as working or using glue all through a woodworking venture, a vise can are available in very. Soft jaws are usually made from a soft metal (usually aluminum), plastic, or wood.

It’s called a leg vise because one of the bench’s legs is an integral part of it – usually forming the inside jaw. The twin-screw vise was popular during the late eighteenth and early nineteenth centuries, particularly with chair makers. Find power gear, hand equipment, air equipment, woodworking equipment, electrical gear, tool storage and workbenches. As you can see in the very top image, the vise is holding a massive overhanging weight of around 200-lbs not accounting for leverage with no additional apron clamping. While the beam keeps the jaw steady and properly aligned, the jaw is driven by a wooden bench screw.

Bench vises, in particular, attach directly to a workbench to hold the workpiece during operations such as sawing, planing, and drilling. But the shoulder vise is a tough build and requires a fifth leg to support it. And, depending on how it’s designed, you have to remember that there are certain parts of the bench around the vise that aren’t as solid as the rest of the top, so beware where you pound. If the vise needs work or has been sitting a long time $.60/lb is more reasonable. When not in use, the vise should be kept closed with the handle in a vertical position. A 9” capacity vise with 3/4” thick pads will give you 7- 1/2” to work with, which is plenty in most situations.

Craftsman 6-inch bench vise is constructed with heavy duty precision-machined anvil to deliver incredible strength for gripping all kinds of objects. Having the right type of woodworking vise can make all the difference when you are in the middle of an important project. I am having a real issue mounting a 9″ Veritas Quick Release vise to the bench I made following Paul’s design. Place the wood in the vise so that as much of the material as possible comes within the faces of the vise; then apply just enough pressure to hold it securely.


Antiques woodworking vice, in full working order with originalnuts and bolts for mounting!! Large pieces of stock insecurely held in the vise may work loose and fall, or throw the operator off balance. Finding the right one could be a daunting task, but, this article will help you find the most reliable one through the following bench vise reviews and a comprehensive buying guideline. I’ll add more holdfast holes after I’ve used the bench for a while and know where they’ll be most useful.

In reality, the half dozen times I have wood long enough to warrant clamping to the bench top is of such little significance compared to the hundred and more twists and turns of dozens of smaller pieces (up to 4′) I do throughout each day. The front jaw probably has threaded holes designed to accommodate flathead machine screws; you will need to countersink the screwheads so that they are set slightly into the wood liner.

The caps are magnetic towards the vise side to prevent steel fillings from attaching themselves to the jaws and keep the clamped part from becoming magnetized. The pin vice is the smallest, holding stickpins or broaches by the pin as the jeweled portion is being worked on. There is also a mini bench vice that is typically used by homeowners in their minor projects of carpentry and metal works.

When they are restored, then I feel the value roughly doubles if a good job is done, and the vise has been made better in both function and looks. I believe that along with Athol, they were the very pinnacle of American vise craftsmanship. I make certain that the vise jaw is fully seated and with no gaps anywhere along the back of the rear vise jaw. Second, for some reason, the handle knob and handle are plated with something that keeps them looking nice long after the rest of the vise gets rusty.

Built into the end of a bench (almost always the right- hand end), the end or tail vise, as it is also called, can be used to clamp workpieces to the bench between its jaws. News relevance is automatically assessed, so some articles not qualifying as Vise news might appear. Vise handles in a horizontal position may project beyond the end of the bench and injure someone. I was thinking that perhaps I can fashion a wedge to go between the bottom of the vise assembly and the bottom of the apron hole, which would transfer vertical energy from the vise into the apron. So if you decide to use a quick-action vise as a tail vise, get the smallest good one you can find.

Typically, the primary function of an end vise is to hold material flat on the surface of the bench, pinched between one or more dogs” sticking up from the top surface of the vise’s jaw and corresponding dogs fitted into holes in the bench surface. The other common type of workbench vise, an end vise”, is stationed at one end of the workbench. Today, the well-equipped shops may have a metal-working vise mounted on the side of their workbench while a woodworking vise on the other end.

Two problems present themselves with bowling alley wood: first, the waxes used on the surface for bowling frequently contain silicone and other substances that can play havoc with work pieces at finishing time – a little silicone on a project will cause trouble with many finishes, and won’t manifest it until it’s too late. A very high quality vise made in the UK. They feature a quick release lead screw in order to make positioning the work easier and faster.