Skateboard Ramp

Im making a mini ramp in my back yard and was wondering if any one knows if 7mm pine ply would be thick enough by its self for the surfacing. North America Plywood grades of lumber are usually not suitable for making quality skateboards unless you can find a full core maple or birch with little knotting or open voids within the cores. A proven design series also…Bill Hays a gogo…good you saw a great ergo design and executed it from that skateboard plywood for ultra strength and contrasting colors. Many manufacturers as mentioned above do get their veneer from a number of suppliers and a number of skateboard companies do get their boards from a number of manufacturers and in good faith are using the best veneer they can get to make your deck from.

Marwood’s Face Grade material is what makes up the 1st and 7th layers of the skateboard sandwich and is what can be seen from the outside. Fiberglass is much stronger than wood, has a little bit less flex than plywood (depending on how thick the fiber plys are and the overall construction of the board) overall, but is a strong sturdy material and is also waterproof. In some instances even alternative woods not durable enough for skateboard manufacturing are used. Rocha assembles new decks using the remnants of broken and discarded skateboards, laminating them together and slicing the resulting stack sideways to create his material.

Now if you were building flat decks with just some concave…you could probably get a few more presses. Most skateboard decks measure about 32 inches long and 8 inches wide, and are roughly rectangular or oval in shape. For a ramp that transitions to the ground, a piece of sheet metal is ideal to make the transition smooth (and to protect the edge of the surface). We get the best hard maple for making solid skateboard and longboard decks here.

Marion Plywood Corporation had become an established source of both high quality panels and veneer, and was perfectly positioned to serve manufacturers in this rapidly expanding market. We performed the same test on a 30 mm bamboo plywood board and it only deflected 4 mm at 1,050 kg of pressure (yes you read that right – 1 ton of pressure flexed the board 4 mm). The length, width, materials, and concave of your skateboard deck determine what you will be able to do on your skateboard.


Since I was using full sheets I used a tape to measure 8 ft down the transition in couple place and marked it. Then, I temporarily screwed a 2√ó4 in place. As skateboarding progresses and develops, so does the number of issues relating to materials and processes in skateboard manufacturing. Maple will expand dramatically when water based glue is applied to it. Too much, or unevenly spread glue between the maple veneer sheets may result in bubbling. If you have any questions regarding the Skateboard kits please do not hesitate to get in touch at 01525 851166. The pressure at which they are pressed is the last major factor in the quality of a skateboard.

Different combinations are chosen by the skate manufacturer to give the decks just the right thickness and strength. According to one of the largest veneer suppliers to the skateboard industry, all of its wood is sourced and harvested from the Great Lakes region of the U.S. and Canada. Maybe, but 9 plys are for the most part heavier then 7 ply decks Almost all skateboard decks and the pros riding them ride 7 ply decks.

While skateboard manufacturers experimented with different thicknesses of veneers that made up decks, little changed in the actual manufacture of skateboards at the beginning of the twenty-first century. Cut the skateboard deck to the desired external shape with a band saw or a jig saw. You might want to lay tar paper under the skatelite ( instructions ), to protect the plywood from the water that seeps through the cracks.

Many manufacturers began using Marion Plywood Corporation products for heelstock and pin planks. Great Lakes Veneer derives its history from its parent company Marion Plywood Corporation, which was founded in 1894 by two Danish immigrants. To do this, you will need a large piece of Styrofoam (at least the size of your plywood), a vacuum with hose attachment, and a vacuum bag big enough to fit your mold and skateboard. Pyramid – Funbox-type ramp made from four banks put in a square pyramid shape, usually surrounding a flat.

This ramp has been done for almost nine months and I skate it almost every day. Jonesville Vert Ramp – Gainesville, Florida The Premiere Vert Ramp in Florida located in Jonesville, Florida. Longboard and Skateboard veneer is typically produced in three grades or plys: Face, Crossband, and Core. Most skateboards are made using laminated sheets – or veneers – of hard North American maple, a durable and somewhat flexible wood. Whether it be skateboard or longboard, maple can hold up through all of the wear and tear.

I was wondering what are some good woods to use in making a longboard I heard that using plywood isn’t good, but I know some people who have pulled off making decks from that wood. Today CSF operates at a capacity of 4,800 decks a day running 80 molds-quadrupling its production in the past year alone. For board building, sheets are cut into rectangles a little larger than the profile of the¬†finished deck.