Fence Calculator

This summer I have a number of big yard projects to conquer and cross off the list. You’ll need to offer each gravel board up to the gap, then mark the point at which it meets the center of the post and cut it to this length before securing with screws. The constant expanding and contracting can also lead to the wood boards splitting or rotting. Just a quick warning to fence builders, one panel on level ground is fine, but when you have any kind of a slope, the horizontal rails wander off into thin air. If you are going to install a gate for people you can measure marks of 4 to 6 inches, but if you plan to install gates for machines and equipment the spaces should be more than 14 inches. The most common reason for installing a wood board on board fence is for privacy.

There are three types of field fencing that I routinely use on this type of fence for pet containment and I have attempted to explain the benefits of each one below. Bear in mind that your fence must be high enough to contain your biggest horse or highest jumper with the bottom board placed low enough to prevent a small pony, miniature horse, or foal from slipping under, and ideally, the spacing between boards should be small enough to prevent a horse from getting its head through. Once the contractor finishes installing each fence post, panels or pickets can be attached to both sides of the post.

The naturalness of the wood properly treated enables excellent performance both from the aesthetic and in terms of structural strength, if the artifact is performed in a workmanlike manner. Prefabricated fence panels come in a standard 1.83m width, and usually in four heights (900mm, 1.2m, 1.52m and 1.83m). Then another 1×6 board is nailed to the top of the spacing, overlapping the other boards by about 1” each. These allow you to use standard fence posts without needing to cut mortises to hold the arris rails.

I then attached the connected rails using two 4 inch screws at the end of each board. Homeowners also risk not adding enough concrete to each hole, which affects the strength of the fence. Fit gravel boards horizontally to the front of the posts across the base of the fence. The fence lines need to be laid out perfectly straight using a string tied tautly between two stakes. But this fence has thicker, higher quality wood, more detail and better fasteners than any store-bought selection.

We believe if your building a wood fence yourself, your going to get the most value for your dollar in the Oklahoma City area from any fence company, by using cedar panels with thick-cut cedar or redwood rails. This articles is general and can apply broadly to many fence styles, but you might want to find specifics on your fence style to compliment these instructions.

Locate your utility and/or sprinkler system lines prior to digging the fence post holes. If your fence will have a gate, make sure to take this into consideration when planning your fence. PATIO DECK-ART DESIGNS OUTDOOR LIVING – maybe use wooden pallets to build privacy fence Look around! The regulations will include setback requirements from your property lines to the fence and maximum allowable heights.

Install this board in the middle of the two boards installed in Step 5. This creates an offset of the joints which makes the boards harder for the horses to remove. In a board-by-board fence and even some panel fences, wood shrinkage causes gaps to form between the boards that compromise the fence’s visual barrier. Before fixing the arris rails to the posts screw lengths of gravel board to the bottom of the fence. This will help you line up the remaining pickets at the same height and get a nice even-looking fence. The 1×6 fence boards are attached to one side of the 2×4 stringer spaced 3” apart.

As close board fencing is constructed using arris rails fitted into mortised post’s you need a minimum of 2 arris rails to make a secure fence. Take particular care when applying wood preservative and put on some safety goggles if this is recommended by the manufacturer. Then make a spacer by cutting an off-cut of timber to 20mm less than the width of a featheredge board.

Short picket fence offers stunning curb appeal with a display of colorful roses, flowers, and vines. To keep from having screw holes in the top (AKA water collectors and potential fence rotting spots) I used PHs to attach this board to top – all PHs will be covered with fence pickets later on. This is done by digging a hole only a little larger in width than the fence post you are supporting, placing the fence post in the hole and then backfilling with the removed soil and ramming to support the fence post. The spacing between posts should never be more that 8-foot (2.4m) for horse fencing if you are wanting a really strong, robust fence that will withstand the weight of horses leaning upon it.

Line posts can be as small as 2.5 inches, but larger ones will provide for a stronger, more durable fence. Cut a 1×6 panel board to length, center it in the panel and tack it into place with a couple of 1-1/2 in. galvanized finish nails at each end (Photo 11).Be sure to angle the nails when driving them in or the tips may project through the other side. Some homeowner’s associations have guidelines or ordinances governing fence construction. And then we run a string line between the posts attached to the house and garage to make sure our fence is straight.

Many people are surprised to learn that constructing a fence usually requires a building permit, though this depends on your jurisdiction There are generally restrictions on the size – 3 or 4 feet in the front yard and 6 or 8 feet in the rear of the house are common standards. An advantage of the double sided construction is that privacy is increased while the ‘open’ form of construction reduces the effects of wind when compared with a solid board fence. Learn how to erect a close board fence around your garden, including tips and tricks that will make it easier and last longer.

The gap between boards on a double sided vertical board fencing should be about the board width less about half the distance between the faces of the rails on each side of the fence. It is also more visible, an important factor when a fence is to be moved periodically to new locations where livestock are not used to seeing it. An electric fence controller is used to energize the wires. This provides a very strong frame for the feather edge boards to be attached to. For additional durability the bay comes complete with a gravel board that fits at the base of the fence this protects the bottom of the feather boards.

With this in mind, being a good neighbor means designing and building a fence that meets your needs while also honoring the needs of the neighborhood. There is no way without trial and error that you will be able to tell if this works ahead of time – unless you have fence wind tunnel data at your hands. If you are building your fence on the property line, discuss it with your neighbor prior to building, to determine if he has objections and to make sure you agree on property lines.

If you are interested in erecting close board fencing at your property, please get in touch with your local branch Our specialists will be happy to offer help and advice and can provide you with a free quote for supply of all relevant materials. You can find how many horizontal rails you need to build a fence by multiplying the number of sections from the previous formula by the number of rails per section. The first board must be positioned vertically on the hoof of protection, with the thicker edge against the stick. A wood fence of six feet is usually high enough to give the homeowner a sense of privacy.

The temporary or movable fence is usually made with one or two strands of smooth wire or a rope or tape with small electric wires woven into it. Tape or rope is more flexible than smooth wire and much easier to handle and move from one location to another. Outdoor shower privacy screens How To Build a Privacy Screen for an Outdoor Hot Tub : How-To : DIY.. I want to make one for my messy craft space! If you need to put up your closeboard fence on a slope, keep the posts and featheredge boards vertical but slope the arris rails evenly, parallel to the ground. The fence will stand correctly—no swings or swags—and no extra cutting and trimming to make pieces fit.

Cut a batten to a length that corresponds to this length and use it to measure where each fence post will be located. I have built this fence before and while it isn’t the cheapest fence you can build, it is on the same expense level as a board on board fence. If you want to build a long lasting and durable wood fence you should try to find the best and most durable wood available in the area and use them as wood posts.

For example, a 24′ fence would need 2 middle posts to create the three 8′ sections, but a 25′ fence would need 3 middle posts at 6.25′ for each section in order to look even and be structurally sound. The feather-edge planks will eventually sit on the gravel board, so it’s crucial to the finished look of the fence to get this step right. If you have a small dog, or even one that sorta kinda likes to dig, the bottom of that fence wall is an open invitation for a doggie jailbreak. Remember, when using a counter rail and capping, it is normal that an amount of post projects above the fence line.

This may mean that if you have already economised with the length of fence post used, a longer fence post will be required. This fence has a solar powered BFT automatic gate operator installed with the optional wireless keypad anchored to a wood post centered between two other wooden post that are serving as stanchions to protect the keypad from accidental damage from cars, trucks, tractors, and construction equipment. Run two builder’s lines between the top and bottom of these posts along the line of the fence and rest the other posts loosely in their holes.

If the boards have been kiln dried, use a nail as a spacer between each one to allow for expansion when the wood is wet. Today, many choices are available for building board fences including PVC plastic, vinyl coated wooden boards, treated wood, and painted wood. You can see through this fence when you’re standing at the right angle (very close to the fence and with limited sight). When any type of moisture penetrates the wood, the water can cause the wood to swell and warp.