Warren is my business partner, as well as my husband so he can get away with the occasional comment like this. Penofin pressure-treated wood stain tones are: Rainier, with golden honey tones to bring out the rich, smooth look of lighter woods; Tahoe, with rich cinnamon tones for that rich, bold look; and Yosemite, showing warm, dark brown tones that complement natural surroundings. Both cleaners and strippers brighten wood surfaces that have dulled and grayed from sun, dirt and rain exposure. In these processes, moisture is removed from the wood before shipment to a lumber dealer.
New pressure treated wood can have a high moisture content and needs to dry out properly before staining/painting, but because ours was so old that wasn’t a concern. Wood is pressure treated to give it protection from attack by insects, microorganisms, decay by fungi and moisture that can cause damage to the wood. Stack wet lumber on a flat surface such as a driveway or patio, use spacers between boards to let air circulate and check the wood for weight and by touch for moisture.
Penetrating stains, properly applied, do NOT seal in the moisture, they inhibit its entry and (when dark colored) help protect against sun damage to the wood and finish, but still breathe enough to let moisture escape on dry days. This process enables the preserved wood to maintain a chemical barrier against termites and decay. Yes, deck stain durability has been trending upwards, but it’s still not universally decent. Plank porch ceiling – Front porch with custom ceiling, cedar posts, stone columns and wood shutters. Oil based stain is very thin and is easily splashed or sprayed on bushes, structures, and underlying materials inadvertently.
Eco Chemical has been serving the treated wood manufacturing industry for more than 20 years, providing high quality waterborne stains in a variety of colors. Apply one coat of a good-quality stain-blocking acrylic latex primer, followed by two topcoats of a good-quality acrylic latex exterior house paint. Pressure-treated (PT) lumber is wood that’s been treated with chemicals to make it resistant to rot and insects.
Wood should be treated with a preservative system to control the destructive activities of these organisms and ensure long-term structural soundness and serviceability. I’ve been testing deck finishing products on wood samples for 25 years and most don’t last nearly as long as you’d expect. You can’t let it dry out before installing unless you can apply a serious amount of pressure on all sides of the wood.
Following construction, most manufacturers of stains and paints recommend a waiting period – from a week to two months – before applying a finish to treated wood, if the project was built with lumber that was not kiln-dried after treatment (KDAT). Take into consideration the location of your deck (does it get sun all day or shade?), what type of wood it is and how you want the finished, treated deck to look. Sanding is an essential first step in achieving an even application of stain or paint. When the wood is dry, it can be painted or stained like any other wood surface. Consider using a stain that’s specially formulated for North Texas fencing materials.
The best remained close to their original color after three years, picked up only a little dirt and mildew, and effectively protected the wood from cracking. If plywood is going to be painted with latex paint or stain, two coats of exterior alkyd or high-quality acrylic primer are recommended first, in order to reduce the chance of cracking. If you notice the color of your wood fence is beginning to fade, it’s time to apply a new coat of stain. When stain is applied too thick, it will not dry properly and it remains sticky to the touch.
The pigments in the stain won’t stick to each other as they do in paints, causing the stain to fail. On new wood, use a product such as NO. 63 to remove mill glaze and open the pores of the wood. For longevity, the best way to go, according to deck pros I’ve talked to, is to use a clear sealer or a semi-transparent stain on your deck. It is recommended decks be finished with a high quality penetrating stain or water repellent.
We used this stain on a cabin, glider and rocker which are all about 8 years old. PAINT & STAIN — The recommendations are the same as above, but it may take longer for the wood to dry out. Large volumes of CCA were being used, and the treated wood products were beginning to be widely distributed, justifying the need for some hard research. If it looks good after washing without bleach then no worries, you are ready for the stain.
I have a job where I need to paint several large pressure treated posts white, I would like to match a competitors quote for 8 year durability. Wood in outdoor exposures, either in ground-contact or in above-ground applications, is susceptible to attack. The real problem comes from 1) the actual water content of the wood and 2) any water repellents included in the product.
Kiln-dried after treatment: Dry treated wood is ideal because you can confidently stain it right away with either oil- or water-based exterior stains. Ready to install in a rich, natural- looking wood tone, it’s an ideal alternative for decks, fences, landscaping, railings, lattice and other outdoor projects. Preserve can be pressure treated for ground-contact exposure, is equally safe around edible plants, and is available in larger posts such as 4×4’s or 6×6’s which may work as the retaining wall or perimeter of a raised vegetable garden.
If you’re in area with a fair amount of moisture and humidity, waterborne, synthetic stains, like DEFY Wood Stains, have some real advantages. If you have a sealant on it you’ll have to make sure it doesn’t bead when water is placed on it. If it beads the oil won’t penetrate into the wood. For maximum brightening wash the wood in full sun, letting the Lime Clean sit for 30-60 minutes in full sun BUT make sure to keep it wet; don’t let it dry out, mist with water every 5-10 minutes so it has maximum strength. The potential for wood deterioration is greatest in hot and humid climates, which allow insects, fungi and bacteria to thrive.
The second is for so-called permanent wood foundations, and the third is to replace the bottom plate on wall framing in basements or other below grade applications, especially when the bottom plate is resting directly on a concrete foundation subject to dampness. It’s less maintenance if you stain it rather than paint it — but if you want longevity with little to no maintenance, consider another material. It is a good idea to choose a sealer with UV stabilisers to lessen the impact of the sun on the wood.
Examine the grass that immediately borders your fence and trim any overgrowth to keep it from spreading rot to your fence. Refinishing a deck with a non-film finish is usually a matter of cleaning, doing minor repairs, and then recoating. Either stain, the 100 or 1500 Series is the best TWP stain for pressure treated pine decks, fences, or other exterior surfaces. With a scrub brush, cleaning the surface of the deck will be as fast as mopping your floor! This wood might still benefit from additional seasoning, but this gives you a head start.
These newer types of treated woods may be less toxic, but they also contain higher levels of copper, so they’re much more corrosive than the old CCA-treated lumber. Work in small sections lightly saturating the surface and immediately back-brush or use pad applicator to eliminate puddling, remove excess and evenly distribute the stain. Every wood species takes pigments differently, and while color charts can provide some guidance, don’t rely on them.
Most pressure treated wood you buy has only been sitting several days, so if you get the opportunity, you can ask the lumber yard how seasoned the wood is when you buy it, otherwise assume it is fresh. In pressure treatment, chemical preservatives are forced into the cellular structure of the wood in a closed cylinder under pressure. Stop by your local hardware store to pick up a specially developed wood cleaner for decks, fences, or other wood structures, and follow the product’s instructions for a thorough cleaning. Testing 1, 2, 3: Make sure you test out the stain before applying it to the whole surface.
I was able to only pressure wash my retaining wall because it is 10 years old and has never been stained or sealed. Regardless of which path you take, it will prepare your deck and restore it to its natural color ready to take a new finish and a visit from family and friends. The deck is right beside the screened-in porch and you access the deck through a soon-to-be-door from the screened-in porch.
Now, a lot of factors play into that, whether or not the material was stored outside at the lumber yard, how long ago it was that they actually treated the wood, and whether your deck is out in the sun or in the shade. The American Wood Protection Association standards provide a list of standardized preservative formulations in the US. The AWPA’s is recognized worldwide, as their ANSI accredited process thoroughly evaluates reviews and standardizes preservatives.
Many people with little experience think that they need to put the stain on thick to better protect their deck. Anyway, around here you do. The old saying if you wanted pressure treated painted… was to let the wood alone for a year and it will go through it’s changes and just about dry out. Depending on the condition of your lumber, you may be able to save time and labor by staining the wood prior to assembly, as in the case of the deck handrails shown. A certain amount of PT preservative will leach to the surface of the wood over time. The water repellent slows down the rate at which the wood absorbs and releases moisture.