Attaching Furring Strips To Concrete Block Walls

Finishing basement walls: furring strips vs stud wall finishing basement walls: furring strips vs stud wall. For securing hardwood strip flooring to subfloor and to secure wood framing or furring strips to brick, block or concrete. If someone else knows a better way to do this, or if it is possible to use an air nailer on concrete block, let me know. I was told that they had tested the gun and had good luck with concrete up to 20 years old, beyond that they had some splatting of the concrete.

An outer layer of foam, a core” layer of steel reinforced concrete and another layer of EPS foam. We use them to anchor tracks for pocket doors, it’s a pretty easy process just takes a little time to pre-drill the concrete. Now that your frame is up, you can attach your panels to the frame using #8 wood screws. You can use either 2x4s or 2x3s placed with the flat side on the wall or you can use 1×3 inch strapping.

Leave a ¼- to ½-inch gap between the ends and drive concrete nails into the floor every 24 inches. Option #2 – Concrete Drop-in Anchor – This anchor is a little more sensitive to install but at a quarter of the cost of the next option, many builders choose this option because of budget concerns. As an example, if you have an 8 foot by 8 foot wall ( 64 square feet ), you should get 2.25 x 64 = 144 t-nuts.

Tapcons work great but are way too much work if you have much to do. Around windows and doors switch from 1×2 to 1×4 or 1×6 to keep your nails farther from the edge of walls. Drive the nail through the board and into the furring strip, so the head is just beneath the board’s surface. An expansion joint in a concrete floor system would occur where it would not be noticed or cause acoustic problems.

Use a hammer drill, drill holes using the correct diameter carbide-tipped masonry bit for the concrete screw diameter in use. If you need more insulation and the floor is too cramped to allow for a full stud-wall, it is possible to install insulation on the exterior of the foundation wall. For specifications and installation of the Concrete Drop-in Anchor click View Product Specs” once you arrive at the link.

Remove the nuts and hang the wall mount on the wall, use washers and tighten down the nuts to secure the wall mount to the wall. If you are using insulation batts or no insulation at all, first cover the walls with a plastic moisture barrier. I usually use 4 inch long 3/8″ sleeve anchors if you are hanging on a plaster wall with brick behind it, and 3 inch long sleeves if its a bare brick or cement wall. If foam is used, however, the wall should be covered with half-inch gypsum-board panels before wood paneling is installed. So I contacted PNI and asked them if this gun would really fire nails into concrete.

Cut vertical furring strips, one for each vertical chalk line, and install similarly. Acid Stain Concrete Floor Design, Pictures, Remodel, Decor and Ideas – page 19…. Loving the molding and stairway. I then build the stud wall lying flat on the floor, but make it an inch and a half shorter than the actual floor to ceiling measurement. Hold the plastic up, from the top, and run it down the length of the wall and across the expanse. Furring strips may create a thermal short” that extends through the XPS insulation layer.

Invest in a cartridge nailer to fasten the furring strips to the concrete, it’s worth the expense when you need to fasten more than 2 or 3 fasteners through concrete. Alternately, furring strips can be attached using construction adhesive that is applied with a caulk gun. Have a look at the clever and cool collection of basement wall ideas below for inspiration.

Foam insulation boards need to be able to sit flush with the entire surface of your basement walls to be efficient. This can be accomplished with furring strips — normally 1 by 2s laid flat against the wall — or a full-stud false wall built in front of the existing foundation wall. Attach wall finish with fasteners that will not penetrate thru the furring strips.